368. Q U I Z - 17

Q U I Z - 17

Science and Technology Questions & Answers

Are you looking for quiz questions and answers about science and technology? You've come at the right place. Check out this Science and Technology quiz and see if you can answer the following questions on science, technology and electronics? Play this quiz to see how good you are at Science and Technology questions. Science and Technology Quiz Questions Here is the list of quiz questions and answers about Science and Technology. Can you answer the following questions on electronics, science and technology? 1] Question: Which is a type of Electrically-Erasable Programmable Read-Only Memory? Flash Flange Fury FRAM 2] Question: What is made from a variety of materials, such as carbon, and inhibits the flow of current? Choke Inductor Resistor Capacitor 3] Question: "FET" is a type of transistor, Its full name is ________ Effect Transistor. Field Factor Flash Force 4] Question: A given signal's second harmonic is twice the given signal's __________ frequency. Fill in the blank? Fourier Foundation Fundamental Field 5] Question: Voltage is sometimes referred to as EMF, or Electromotive ________? Field Factor Flash Force 6] Question: When measuring the characteristics of a small-signal amplifier, say for a radio receiver, one might be concerned with its "Noise ________"? Fundamental Fall Force Figure 7] Question: The average power (in watts) used by a 20 to 25 inch home color television is ________? 70-100 25-50 500-800 Over 1000 Question: The most common format for a home video recorder is VHS. VHS stands for ________? Video Home System Very High Speed Video Horizontal Standard Voltage House Standard Question: If the picture is stretched or distorted up and down like a fun house mirror the circuit to adjust or repair is ________? Vertical Tuning Horizontal Filament Question: The electromagnetic coils on the neck of the picture tube or tubes which pull the electron beam from side to side and up and down are called a ________? Transformer Yoke Capacitor Diode Question: The input used by an antenna or cable to a TV set uses ________ frequencies? IF RF AF SAP Question: The transformer that develops the high voltage in a home television is commonly called a ________? Tesla coil Flyback Yoke Van de Graaf Question: Most modern TV's draw power even if turned off. The circuit the power is used in does what function? Sound Remote Control Color Balance High Voltage Question: In a color television set using a picture tube a high voltage is used to accelerate electron beams to light the screen. What is that voltage? 500 Volts 5 Thousand Volts 25 Thousand Volts 100 Thousand Volts Question: The NTSC (National Television Standards Committee) is also used in the country of ________? Japan France Germany England Question: In the USA, the television broadcast standard is ________? PAL NTSC SECAM RGB Question: Which is NOT an acceptable method of distributing small power outlets throughout an open plan office area? Power Poles Power Skirting Flush Floor Ducting Extension Cords Question: In the UK, what type of installation requires a fireman's switch? Neon Lighting High Pressure Sodium Lighting Water Features Hotel Rooms Question: What will a UPS be used for in a building? To provide power to essential equipment To monitor building electricity use To carry messages between departments To control lighting and power systems Question: Larger buildings may be supplied with a medium voltage electricity supply, and will required a substation or mini-sub. What is the main item of equipment contained in these? Transformer Transponder Transducer Converter Question: Some lasers are referred to as being CW. What does CW mean? Circular wave Constant white Continuous wave Clear white Question: What is the process responsible for producing photons in a diode laser? Fermi level shift Majority carrier injection Carrier freeze out Electron-hole recombination Question: What are three types of lasers? Gas, Metal Vapor, Rock Pointer, Diode, CD Diode, Inverted, Pointer Gas, Solid State, Diode Question: What was the active medium used in the first working laser ever constructed? A Diamond Block Helium-Neon Gas A Ruby Rod Carbon Dioxide Gas Question: After the first photons of light are produced, which process is responsible for amplification of the light? Blackbody Radiation Stimulated Emission Planck'S Radiation Einstein Oscillation Question: Once the active medium is excited, the first photons of light are produced by which physical process? Blackbody Radiation Spontaneous Emission Synchrotron Radiation Planck'S Oscillation Question: The first step to getting output from a laser is to excite an active medium. What is this process called? Pumping Exciting Priming Raising Question: What does AM mean? Angelo Marconi Anno Median Amplitude Modulation Amperes Question: What frequency range is the High Frequency band? 100 kHz 1 GHz 30 to 300 MHz 3 to 30 MHz Question: What does EPROM stand for? Electric Programmable Read Only Memory Erasable Programmable Read Only Memory Evaluable Philotic Random Optic Memory Every Person Requires One Mind Question: What does the term PLC stand for? Programmable Lift Computer Program List Control Programmable Logic Controller Piezo Lamp Connector Question: Which motor is NOT suitable for use as a DC machine? Permanent Magnet Motor Series Motor Squirrel Cage Motor Synchronous Motor Question: What does VVVF stand for? Variant Voltage Vile Frequency Variable Velocity Variable Fun Very Very Vicious Frequency Variable Voltage Variable Frequency Question: The sampling rate, (how many samples per second are stored) for a CD is...? 48.4 kHz 22,050 Hz 44.1 kHz 48 kHz Question: A Compact disc (according to the original CD specifications) hold how many minutes of music? 74 mins 56 mins 60 mins 90 mins Question: Sometimes computers and cash registers in a foodmart are connected to a UPS system. What does UPS mean? United Parcel Service Uniform Product Support Under Paneling Storage Uninterruptable Power Supply Question: What does AC and DC stand for in the electrical field? Alternating Current and Direct Current A Rock Band from Australia Average Current and Discharged Capacitor Atlantic City and District of Columbia Question: Which consists of two plates separated by a dielectric and can store a charge? Inductor Capacitor Transistor Relay Have a science and technology question? Ask it! We are always available to answer your questions and help you understand science and technology. This science and technology quiz will be updated on regular basis. A total of 146 users are reading this article.

367. R A D I O

R A D I O

Receive + Amplify + Detect + Intelligence + give Output

How radio communication works. Information such as sound is transformed into an electronic signal which is applied to a transmitter. The transmitter sends the information through space on a radio wave (electromagnetic wave). A receiver intercepts some of the radio wave and extracts the information-bearing electronic signal, which is converted back to its original form by a transducer such as a speaker.

Radio is the wireless transmission of signals through free space by electromagnetic radiation of a frequency significantly below that of visible light, in the radio frequency range, from about 30 kHz to 300 GHz. These waves are called radio waves. Electromagnetic radiation travels by means of oscillating electromagnetic fields that pass through the air and the vacuum of space.

Information, such as sound, is carried by systematically changing (modulating) some property of the radiated waves, such as their amplitude, frequency, phase, or pulse width. When radio waves strike an electrical conductor, the oscillating fields induce an alternating current in the conductor. The information in the waves can be extracted and transformed back into its original form.

Etymology

The etymology of "radio" or "radiotelegraphy" reveals that it was called "wireless telegraphy," which was shortened to "wireless" in Britain. The prefix radio- in the sense of wireless transmission, was first recorded in the word radioconductor, a description provided by the French physicist Édouard Branly in 1897. It is based on the verb to radiate (in Latin "radius" means "spoke of a wheel, beam of light, ray").

The word "radio" also appears in a 1907 article by Lee De Forest. It was adopted by the United States Navy in 1912, to distinguish radio from several other wireless communication technologies, such as the photophone. The term became common by the time of the first commercial broadcasts in the United States in the 1920s. (The noun "broadcasting" itself came from an agricultural term, meaning "scattering seeds widely.") The term was adopted by other languages in Europe and Asia. British Commonwealth countries continued to commonly use the term "wireless" until the mid-20th century, though the magazine of the BBC in the UK has been called Radio Times ever since it was first published in the early 1920s.

In recent years the more general term "wireless" has gained renewed popularity through the rapid growth of short-range computer networking, e.g., Wireless Local Area Network (WLAN), Wi-Fi, and Bluetooth, as well as mobile telephony, e.g., GSM and UMTS. Today, the term "radio" specifies the actual type of transceiver device or chip, whereas "wireless" refers to the lack of physical connections; one talks about radio transceivers, but about wireless devices and wireless sensor networks.

Processes

Radio systems used for communications will have the following elements. With more than 100 years of development, each process is implemented by a wide range of methods, specialized for different communications purposes.

Transmitter and modulation

Each system contains a transmitter. This consists of a source of electrical energy, producing alternating current of a desired frequency of oscillation. The transmitter contains a system to modulate (change) some property of the energy produced to impress a signal on it. This modulation might be as simple as turning the energy on and off, or altering more subtle properties such as amplitude, frequency, phase, or combinations of these properties. The transmitter sends the modulated electrical energy to a tuned resonant antenna; this structure converts the rapidly changing alternating current into an electromagnetic wave that can move through free space (sometimes with a particular polarization).

An audio signal (top) may be carried by an AM or FM radio wave.

Amplitude modulation of a carrier wave works by varying the strength of the transmitted signal in proportion to the information being sent. For example, changes in the signal strength can be used to reflect the sounds to be reproduced by a speaker, or to specify the light intensity of television pixels. It was the method used for the first audio radio transmissions, and remains in use today. "AM" is often used to refer to the mediumwave broadcast band (see AM radio).

Frequency modulation varies the frequency of the carrier. The instantaneous frequency of the carrier is directly proportional to the instantaneous value of the input signal. Digital data can be sent by shifting the carrier's frequency among a set of discrete values, a technique known as frequency-shift keying.

FM is commonly used at VHF radio frequencies for high-fidelity broadcasts of music and speech (see FM broadcasting). Normal (analog) TV sound is also broadcast using FM.

Angle modulation alters the instantaneous phase of a carrier wave to transmit a signal. It is another term for Phase modulation.

Antenna

Rooftop television antennas in Israel. Yagi-Uda antennas like these six are widely used at VHF and UHF frequencies.

An antenna (or aerial) is an electrical device which converts electric currents into radio waves, and vice versa. It is usually used with a radio transmitter or radio receiver. In transmission, a radio transmitter applies an oscillating radio frequency electric current to the antenna's terminals, and the antenna radiates the energy from the current as electromagnetic waves (radio waves). In reception, an antenna intercepts some of the power of an electromagnetic wave in order to produce a tiny voltage at its terminals, that is applied to a receiver to be amplified. An antenna can be used for both transmitting and receiving.

Propagation

Once generated, electromagnetic waves travel through space either directly, or have their path altered by reflection, refraction or diffraction. The intensity of the waves diminishes due to geometric dispersion (the inverse-square law); some energy may also be absorbed by the intervening medium in some cases. Noise will generally alter the desired signal; this electromagnetic interference comes from natural sources, as well as from artificial sources such as other transmitters and accidental radiators. Noise is also produced at every step due to the inherent properties of the devices used. If the magnitude of the noise is large enough, the desired signal will no longer be discernible; this is the fundamental limit to the range of radio communications.

Resonance

Electrical resonance of tuned circuits in radios allow individual stations to be selected. A resonant circuit will respond strongly to a particular frequency, and much less so to differing frequencies. This allows the radio receiver to discriminate between multiple signals differing in frequency.

Receiver and demodulation

A Crystal Receiver, consisting of an antenna, rheostat, coil, crystal rectifier, capacitor, headphones and ground connection.

The electromagnetic wave is intercepted by a tuned receiving antenna; this structure captures some of the energy of the wave and returns it to the form of oscillating electrical currents. At the receiver, these currents are demodulated, which is conversion to a usable signal form by a detector sub-system. The receiver is "tuned" to respond preferentially to the desired signals, and reject undesired signals.

Early radio systems relied entirely on the energy collected by an antenna to produce signals for the operator. Radio became more useful after the invention of electronic devices such as the vacuum tube and later the transistor, which made it possible to amplify weak signals. Today radio systems are used for applications from walkie-talkie children's toys to the control of space vehicles, as well as for broadcasting, and many other applications.

A radio receiver receives its input from an antenna, uses electronic filters to separate a wanted radio signal from all other signals picked up by this antenna, amplifies it to a level suitable for further processing, and finally converts through demodulation and decoding the signal into a form usable for the consumer, such as sound, pictures, digital data, measurement values, navigational positions, etc.^[2]

Radio band

Light Comparison
Name	Wavelength	Frequency (Hz)	Photon Energy (eV)
Gamma ray	less than 0.01 nm	more than 10 EHZ	100 keV - 300+ GeV
X-Ray	0.01 to 10 nm	30 PHz - 30 EHZ	120 eV to 120 keV
Ultraviolet	10 nm - 400 nm	30 EHZ - 790 THz	3 eV to 124 eV
Visible	390 nm - 750 nm	790 THz - 405 THz	1.7 eV - 3.3 eV
Infrared	750 nm - 1 mm	405 THz - 300 GHz	1.24 meV - 1.7 eV
Microwave	1 mm - 1 meter	300 GHz - 300 MHz	1.24 meV - 1.24 µeV
Radio	1 mm - km	300 GHz - 3 Hz	1.24 meV - 12.4 feV

Radio frequencies occupy the range from a few hertz to 300 GHz, although commercially important uses of radio use only a small part of this spectrum.

Other types of electromagnetic radiation, with frequencies above the RF range, are infrared, visible light, ultraviolet, X-rays and gamma rays. Since the energy of an individual photon of radio frequency is too low to remove an electron from an atom, radio waves are classified as non-ionizing radiation.

Communication Systems

A radio communication system sends signals by radio.^[4] Types of radio communication systems deployed depend on technology, standards, regulations, radio spectrum allocation, user requirements, service positioning, and investment.^[5]

The radio equipment involved in communication systems includes a transmitter and a receiver, each having an antenna and appropriate terminal equipment such as a microphone at the transmitter and a loudspeaker at the receiver in the case of a voice-communication system.

The power consumed in a transmitting station varies depending on the distance of communication and the transmission conditions. The power received at the receiving station is usually only a tiny fraction of the transmitter's output, since communication depends on receiving the information, not the energy, that was transmitted.

Classical radio communications systems use frequency-division multiplexing (FDM) as a strategy to split up and share the available radio-frequency bandwidth for use by different parties communications concurrently. Modern radio communication systems include those that divide up a radio-frequency band by time-division multiplexing (TDM) and code-division multiplexing (CDM) as alternatives to the classical FDM strategy. These systems offer different tradeoffs in supporting multiple users, beyond the FDM strategy that was ideal for broadcast radio but less so for applications such as mobile telephony.

A radio communication system may send information only one way. For example, in broadcasting a single transmitter sends signals to many receivers. Two stations may take turns sending and receiving, using a single radio frequency; this is called "simplex." By using two radio frequencies, two stations may continuously and concurrently send and receive signals - this is called "duplex" operation.

Uses of radio

Early uses were maritime, for sending telegraphic messages using Morse code between ships and land. The earliest users included the Japanese Navy scouting the Russian fleet during the Battle of Tsushima in 1905. One of the most memorable uses of marine telegraphy was during the sinking of the RMS Titanic in 1912, including communications between operators on the sinking ship and nearby vessels, and communications to shore stations listing the survivors.

Radio was used to pass on orders and communications between armies and navies on both sides in World War I; Germany used radio communications for diplomatic messages once it discovered that its submarine cables had been tapped by the British. The United States passed on President Woodrow Wilson's Fourteen Points to Germany via radio during the war. Broadcasting began from San Jose, California in 1909, and became feasible in the 1920s, with the widespread introduction of radio receivers, particularly in Europe and the United States. Besides broadcasting, point-to-point broadcasting, including telephone messages and relays of radio programs, became widespread in the 1920s and 1930s. Another use of radio in the pre-war years was the development of detection and locating of aircraft and ships by the use of radar (RAdio Detection And Ranging).

Today, radio takes many forms, including wireless networks and mobile communications of all types, as well as radio broadcasting. Before the advent of television, commercial radio broadcasts included not only news and music, but dramas, comedies, variety shows, and many other forms of entertainment (the era from the late 1920s to the mid-1950s is commonly called radio's "Golden Age"). Radio was unique among methods of dramatic presentation in that it used only sound. For more, see radio programming.

Audio

A Fisher 500 AM/FM hi-fi receiver from 1959.

AM radio uses amplitude modulation, in which the amplitude of the transmitted signal is made proportional to the sound amplitude captured (transduced) by the microphone, while the transmitted frequency remains unchanged. Transmissions are affected by static and interference because lightning and other sources of radio emissions on the same frequency add their amplitudes to the original transmitted amplitude.

In the early part of the 20th century, American AM radio stations broadcast with powers as high as 500 kW, and some could be heard worldwide; these stations' transmitters were commandeered for military use by the US Government during World War II. Currently, the maximum broadcast power for a civilian AM radio station in the United States and Canada is 50 kW, and the majority of stations that emit signals this powerful were grandfathered in (see List of 50 kW AM radio stations in the United States). In 1986 KTNN received the last granted 50,000 watt license. These 50 kW stations are generally called "clear channel" stations (not to be confused with Clear Channel Communications), because within North America each of these stations has exclusive use of its broadcast frequency throughout part or all of the broadcast day.

Bush House,old home of the BBC World Service.

FM broadcast radio sends music and voice with less noise than AM radio (It is often mistakenly thought that FM is higher fidelity than AM but that is not the case. AM is capable of the same audio bandwidth that FM employs. AM receivers typically use narrower filters in the receiver to recover the signal with less noise; AM stereo receivers can reproduce the same audio bandwidth that FM does due to the wider filter used in an AM stereo receiver, but nowadays, AM radios limit the audio bandpass to 3–5 kHz maximum). In frequency modulation, amplitude variation at the microphone causes the transmitter frequency to fluctuate. Because the audio signal modulates the frequency and not the amplitude, an FM signal is not subject to static and interference in the same way as AM signals. Due to its need for a wider bandwidth, FM is transmitted in the Very High Frequency (VHF, 30 MHz to 300 MHz) radio spectrum.

VHF radio waves act more like light, traveling in straight lines; hence the reception range is generally limited to about 50–200 miles. During unusual upper atmospheric conditions, FM signals are occasionally reflected back towards the Earth by the ionosphere, resulting in long distance FM reception. FM receivers are subject to the capture effect, which causes the radio to only receive the strongest signal when multiple signals appear on the same frequency. FM receivers are relatively immune to lightning and spark interference.

High power is useful in penetrating buildings, diffracting around hills, and refracting in the dense atmosphere near the horizon for some distance beyond the horizon. Consequently, 100,000 watt FM stations can regularly be heard up to 100 miles (160 km) away, and farther (e.g., 150 miles, 240 km) if there are no competing signals.

A few old, "grandfathered" stations do not conform to these power rules. WBCT-FM (93.7) in Grand Rapids, Michigan, US, runs 320,000 watts ERP, and can increase to 500,000 watts ERP by the terms of its original license. Such a huge power level does not usually help to increase range as much as one might expect, because VHF frequencies travel in nearly straight lines over the horizon and off into space. Nevertheless, when there were fewer FM stations competing, this station could be heard near Bloomington, Illinois, US, almost 300 miles (500 km) away.^{[citation needed]}

FM subcarrier services are secondary signals transmitted in a "piggyback" fashion along with the main program. Special receivers are required to utilize these services. Analog channels may contain alternative programming, such as reading services for the blind, background music or stereo sound signals. In some extremely crowded metropolitan areas, the sub-channel program might be an alternate foreign-language radio program for various ethnic groups. Sub-carriers can also transmit digital data, such as station identification, the current song's name, web addresses, or stock quotes. In some countries, FM radios automatically re-tune themselves to the same channel in a different district by using sub-bands.

Aviation voice radios use VHF AM. AM is used so that multiple stations on the same channel can be received. (Use of FM would result in stronger stations blocking out reception of weaker stations due to FM's capture effect). Aircraft fly high enough that their transmitters can be received hundreds of miles (or kilometres) away, even though they are using VHF.

Degen DE1103, an advanced world mini-receiver with single sideband modulation and dual conversion

Marine voice radios can use single sideband voice (SSB) in the shortwave High Frequency (HF—3 MHz to 30 MHz) radio spectrum for very long ranges or narrowband FM in the VHF spectrum for much shorter ranges. Narrowband FM sacrifices fidelity to make more channels available within the radio spectrum, by using a smaller range of radio frequencies, usually with five kHz of deviation, versus the 75 kHz used by commercial FM broadcasts, and 25 kHz used for TV sound.

Government, police, fire and commercial voice services also use narrowband FM on special frequencies. Early police radios used AM receivers to receive one-way dispatches.

Civil and military HF (high frequency) voice services use shortwave radio to contact ships at sea, aircraft and isolated settlements. Most use single sideband voice (SSB), which uses less bandwidth than AM. On an AM radio SSB sounds like ducks quacking, or the adults in a Charlie Brown cartoon. Viewed as a graph of frequency versus power, an AM signal shows power where the frequencies of the voice add and subtract with the main radio frequency. SSB cuts the bandwidth in half by suppressing the carrier and one of the sidebands. This also makes the transmitter about three times more powerful, because it doesn't need to transmit the unused carrier and sideband.

TETRA, Terrestrial Trunked Radio is a digital cell phone system for military, police and ambulances. Commercial services such as XM, WorldSpace and Sirius offer encrypted digital Satellite radio.

Telephony

Mobile phones transmit to a local cell site (transmitter/receiver) that ultimately connects to the public switched telephone network (PSTN) through an optic fiber or microwave radio and other network elements. When the mobile phone nears the edge of the cell site's radio coverage area, the central computer switches the phone to a new cell. Cell phones originally used FM, but now most use various digital modulation schemes. Recent developments in Sweden (such as DROPme) allow for the instant downloading of digital material from a radio broadcast (such as a song) to a mobile phone.

Satellite phones use satellites rather than cell towers to communicate.

Video

Television sends the picture as AM and the sound as AM or FM, with the sound carrier a fixed frequency (4.5 MHz in the NTSC system) away from the video carrier. Analog television also uses a vestigial sideband on the video carrier to reduce the bandwidth required.

Digital television uses 8VSB modulation in North America (under the ATSC digital television standard), and COFDM modulation elsewhere in the world (using the DVB-T standard). A Reed–Solomon error correction code adds redundant correction codes and allows reliable reception during moderate data loss. Although many current and future codecs can be sent in the MPEG transport stream container format, as of 2006 most systems use a standard-definition format almost identical to DVD: MPEG-2 video in Anamorphic widescreen and MPEG layer 2 (MP2) audio. High-definition television is possible simply by using a higher-resolution picture, but H.264/AVC is being considered as a replacement video codec in some regions for its improved compression. With the compression and improved modulation involved, a single "channel" can contain a high-definition program and several standard-definition programs.

Navigation

All satellite navigation systems use satellites with precision clocks. The satellite transmits its position, and the time of the transmission. The receiver listens to four satellites, and can figure its position as being on a line that is tangent to a spherical shell around each satellite, determined by the time-of-flight of the radio signals from the satellite. A computer in the receiver does the math.

Radio direction-finding is the oldest form of radio navigation. Before 1960 navigators used movable loop antennas to locate commercial AM stations near cities. In some cases they used marine radiolocation beacons, which share a range of frequencies just above AM radio with amateur radio operators. LORAN systems also used time-of-flight radio signals, but from radio stations on the ground.

VOR (Very High Frequency Omnidirectional Range), systems (used by aircraft), have an antenna array that transmits two signals simultaneously. A directional signal rotates like a lighthouse at a fixed rate. When the directional signal is facing north, an omnidirectional signal pulses. By measuring the difference in phase of these two signals, an aircraft can determine its bearing or radial from the station, thus establishing a line of position. An aircraft can get readings from two VORs and locate its position at the intersection of the two radials, known as a "fix."

When the VOR station is collocated with DME (Distance Measuring Equipment), the aircraft can determine its bearing and range from the station, thus providing a fix from only one ground station. Such stations are called VOR/DMEs. The military operates a similar system of navaids, called TACANs, which are often built into VOR stations. Such stations are called VORTACs. Because TACANs include distance measuring equipment, VOR/DME and VORTAC stations are identical in navigation potential to civil aircraft.

Radar

Radar (Radio Detection And Ranging) detects objects at a distance by bouncing radio waves off them. The delay caused by the echo measures the distance. The direction of the beam determines the direction of the reflection. The polarization and frequency of the return can sense the type of surface. Navigational radars scan a wide area two to four times per minute. They use very short waves that reflect from earth and stone. They are common on commercial ships and long-distance commercial aircraft.

General purpose radars generally use navigational radar frequencies, but modulate and polarize the pulse so the receiver can determine the type of surface of the reflector. The best general-purpose radars distinguish the rain of heavy storms, as well as land and vehicles. Some can superimpose sonar data and map data from GPS position.

Search radars scan a wide area with pulses of short radio waves. They usually scan the area two to four times a minute. Sometimes search radars use the Doppler effect to separate moving vehicles from clutter. Targeting radars use the same principle as search radar but scan a much smaller area far more often, usually several times a second or more. Weather radars resemble search radars, but use radio waves with circular polarization and a wavelength to reflect from water droplets. Some weather radar use the Doppler effect to measure wind speeds.

Data (digital radio)

Most new radio systems are digital, see also: Digital TV, Satellite Radio, Digital Audio Broadcasting. The oldest form of digital broadcast was spark gap telegraphy, used by pioneers such as Marconi. By pressing the key, the operator could send messages in Morse code by energizing a rotating commutating spark gap. The rotating commutator produced a tone in the receiver, where a simple spark gap would produce a hiss, indistinguishable from static. Spark-gap transmitters are now illegal, because their transmissions span several hundred megahertz. This is very wasteful of both radio frequencies and power.

The next advance was continuous wave telegraphy, or CW (Continuous Wave), in which a pure radio frequency, produced by a vacuum tube electronic oscillator was switched on and off by a key. A receiver with a local oscillator would "heterodyne" with the pure radio frequency, creating a whistle-like audio tone. CW uses less than 100 Hz of bandwidth. CW is still used, these days primarily by amateur radio operators (hams). Strictly, on-off keying of a carrier should be known as "Interrupted Continuous Wave" or ICW or on-off keying (OOK).

Radioteletype equipment usually operates on short-wave (HF) and is much loved by the military because they create written information without a skilled operator. They send a bit as one of two tones using frequency-shift keying. Groups of five or seven bits become a character printed by a teleprinter. From about 1925 to 1975, radioteletype was how most commercial messages were sent to less developed countries. These are still used by the military and weather services.

Aircraft use a 1200 Baud radioteletype service over VHF to send their ID, altitude and position, and get gate and connecting-flight data. Microwave dishes on satellites, telephone exchanges and TV stations usually use quadrature amplitude modulation (QAM). QAM sends data by changing both the phase and the amplitude of the radio signal. Engineers like QAM because it packs the most bits into a radio signal when given an exclusive (non-shared) fixed narrowband frequency range. Usually the bits are sent in "frames" that repeat. A special bit pattern is used to locate the beginning of a frame.

Modern GPS receivers.

Communication systems that limit themselves to a fixed narrowband frequency range are vulnerable to jamming. A variety of jamming-resistant spread spectrum techniques were initially developed for military use, most famously for Global Positioning System satellite transmissions. Commercial use of spread spectrum began in the 1980s. Bluetooth, most cell phones, and the 802.11b version of Wi-Fi each use various forms of spread spectrum.

Systems that need reliability, or that share their frequency with other services, may use "coded orthogonal frequency-division multiplexing" or COFDM. COFDM breaks a digital signal into as many as several hundred slower subchannels. The digital signal is often sent as QAM on the subchannels. Modern COFDM systems use a small computer to make and decode the signal with digital signal processing, which is more flexible and far less expensive than older systems that implemented separate electronic channels.

COFDM resists fading and ghosting because the narrow-channel QAM signals can be sent slowly. An adaptive system, or one that sends error-correction codes can also resist interference, because most interference can affect only a few of the QAM channels. COFDM is used for Wi-Fi, some cell phones, Digital Radio Mondiale, Eureka 147, and many other local area network, digital TV and radio standards.